Oxygen Ionic-Conducting Ceramics for Gas Separation and Reaction Applications

158017-Thumbnail Image.png
Description
Mixed-ionic electronic conducting (MIEC) oxides have drawn much attention from researchers because of their potential in high temperature separation processes. Among many materials available, perovskite type and fluorite type oxides are the most studied for their excellent oxygen ion transport

Mixed-ionic electronic conducting (MIEC) oxides have drawn much attention from researchers because of their potential in high temperature separation processes. Among many materials available, perovskite type and fluorite type oxides are the most studied for their excellent oxygen ion transport property. These oxides not only can be oxygen adsorbent or O2-permeable membranes themselves, but also can be incorporated with molten carbonate to form dual-phase membranes for CO2 separation.

Oxygen sorption/desorption properties of perovskite oxides with and without oxygen vacancy were investigated first by thermogravimetric analysis (TGA) and fixed-bed experiments. The oxide with unique disorder-order phase transition during desorption exhibited an enhanced oxygen desorption rate during the TGA measurement but not in fixed-bed demonstrations. The difference in oxygen desorption rate is due to much higher oxygen partial pressure surrounding the sorbent during the fixed-bed oxygen desorption process, as revealed by X-ray diffraction (XRD) patterns of rapidly quenched samples.

Research on using perovskite oxides as CO2-permeable dual-phase membranes was subsequently conducted. Two CO2-resistant MIEC perovskite ceramics, Pr0.6Sr0.4Co0.2Fe0.8 O3-δ (PSCF) and SrFe0.9Ta0.1O3-δ (SFT) were chosen as support materials for membrane synthesis. PSCF-molten carbonate (MC) and SFT-MC membranes were prepared for CO2-O2 counter-permeation. The geometric factors for the carbonate phase and ceramic phase were used to calculate the effective carbonate and oxygen ionic conductivity in the carbonate and ceramic phase. When tested in CO2-O2 counter-permeation set-up, CO2 flux showed negligible change, but O2 flux decreased by 10-32% compared with single-component permeation. With CO2 counter-permeation, the total oxygen permeation flux is higher than that without counter-permeation.

A new concept of CO2-permselective membrane reactor for hydrogen production via steam reforming of methane (SRM) was demonstrated. The results of SRM in the membrane reactor confirm that in-situ CO2 removal effectively promotes water-gas shift conversion and thus enhances hydrogen yield. A modeling study was also conducted to assess the performance of the membrane reactor in high-pressure feed/vacuum sweep conditions, which were not carried out due to limitations in current membrane testing set-up. When 5 atm feed pressure and 10-3 atm sweep pressure were applied, the membrane reactor can produce over 99% hydrogen stream in simulation.
Date Created
2020
Agent

Gasification of Municipal Solid Waste for Power Generation

131289-Thumbnail Image.png
Description
The paper analyzes the growing desire to use waste-to-energy strategies on municipal solid waste (MSW) to generate power. The two waste-to-energy technologies that will be explored are incineration and gasification. The background of these two technologies will be explained because

The paper analyzes the growing desire to use waste-to-energy strategies on municipal solid waste (MSW) to generate power. The two waste-to-energy technologies that will be explored are incineration and gasification. The background of these two technologies will be explained because incineration, which has been the pioneering technology for the past century, has come to be rivaled by gasification with its unique purification feature. Following this section, gasification and incineration power generation are studied to conclude which technology is sounder. This study will be conducted via an analysis to find the thermal and exergetic efficiencies and emissions of each. After analyzing the two technologies, both utilizing a vapor cogeneration power system, their efficiencies were found. For the gasification process, the thermal efficiency was 26% and the exergetic efficiency was 59%. The incineration process had a thermal efficiency of 25% and an exergetic efficiency of 55%. Lastly, the emission from the power generation of each method was explored to see which system had a greater impact on the environment. It was found that the primary emissions of these technologies were carbon dioxide and water.
Date Created
2020-05
Agent

Hydrothermal Liquefaction of Micro-Algae to Produce Liquid Biofuels

131946-Thumbnail Image.png
Description
Fossil fuels are currently the main source of energy in the world’s transportation sector. They are also the primary contributor to carbon emissions in the atmosphere, leading to adverse climate effects. The objective of the following research is to increase

Fossil fuels are currently the main source of energy in the world’s transportation sector. They are also the primary contributor to carbon emissions in the atmosphere, leading to adverse climate effects. The objective of the following research is to increase the yield and efficiency of algal biofuel in order to establish algal-derived fuel as a competitive alternative to predominantly used fossil fuels. Using biofuel commercially will reduce the cost of production and ultimately decrease additional carbon emissions. Experiments were performed using hydrothermal liquefaction (HTL) to determine which catalyst would enhance the algal biocrude oil and result in the highest quality biofuel product, as well as to find the optimal combination of processing temperature and manure co-liquefaction of biomass ratio. For the catalytic upgrading experiments, Micractenium Immerum algae was used in conjunction with pure H2, Pt/C, MO2C, and HZSM-5 catalysts at 350℃ and 400℃, 430 psi, and a 30-minute residence time to investigate the effects of catalyst choice and temperature on the crude oil yield. While all catalysts increased the carbon content of the crude oil, it was found that using HZSM-5 at 350℃ resulted in the greatest overall yield of about 75%. However, the Pt/C catalyst increased the HHV from 34.26 MJ/kg to 43.26 MJ/kg. Cyanidioschyzon merolae (CM) algae and swine manure were utilized in the co-liquefaction experiments, in ratios (algae to swine) of 80:20, 50:50, and 20:80 at temperatures of 300℃ and 330℃. It was found that a ratio of 80:20 at 330℃ produced the highest biocrude oil yield of 29.3%. Although the 80:20 experiments had the greatest biomass conversion and best supported the deacidification of the oil product, the biocrude oil had a HHV of 33.58 MJ/kg, the lowest between the three different ratios. However, all calorific values were relatively close to each other, suggesting that both catalytic upgrading and co-liquefaction can increase the efficiency and economic viability of algal biofuel.
Date Created
2020-05
Agent

Modeling the Flowability of Granular Materials

157933-Thumbnail Image.png
Description
This thesis investigated the effects of differing diameters and varying moisture content on the flowability properties of granular glass beads through use of a Freeman FT4 Powder Rheometer. These parameters were tested in order to construct an empirical model to

This thesis investigated the effects of differing diameters and varying moisture content on the flowability properties of granular glass beads through use of a Freeman FT4 Powder Rheometer. These parameters were tested in order to construct an empirical model to predict flowability properties of glass beads at differing size ranges and moisture contents. The final empirical model outputted an average error of 8.73% across all tested diameters and moisture ranges.

Mohr's circles were constructed from experimentally-obtained shear stress values to quantitatively describe flowability of tested materials in terms of a flow function parameter. A high flow function value (>10) was indicative of a good flow.

By testing 120-180 µm, 120-350 µm, 180-250 µm, 250-350 µm, 430-600 µm, and 600-850 µm glass bead diameter ranges, an increase in size was seen to result in higher flow function values. The limitations of testing using the FT4 became apparent as inconsistent flow function values were obtained at 0% moisture with size ranges above 120-180 µm, or at flow function values of >21. Bead sizes larger than 430 µm showed significant standard deviation over all tested trials--when excluding size ranges above that value, the empirical model showed an average error of only 6.45%.

Wet material testing occurred at all tested glass bead size ranges using a deionized water content of 0%, 1%, 5%, 15%, and 20% by weight. The results of such testing showed a decrease in the resulting flow function parameter as more water content was added. However, this trend changed as 20% moisture content was achieved; the wet material became supersaturated, and an increase in flow function values was observed. The empirical model constructed, therefore, neglected the 20% moisture content regime.
Date Created
2019
Agent

Zwitterionic poly (arylene ether sulfone) copolymers: membrane applications and fundamentals

157681-Thumbnail Image.png
Description
Zwitterionic polymers, due to their supurior capability of electrostatically induced hydration, have been considered as effective functionalities to alleviate bio-fouling of reverse osmosis (RO) membranes. Bulk modification of polysulfone-based matrices to improve hydrophilicity, on the other hand, is favored due

Zwitterionic polymers, due to their supurior capability of electrostatically induced hydration, have been considered as effective functionalities to alleviate bio-fouling of reverse osmosis (RO) membranes. Bulk modification of polysulfone-based matrices to improve hydrophilicity, on the other hand, is favored due to the high membrane performance, processibility, and intrinsic chlorine resistance. Here a novel synthetic method was demonstrated to prepare zwitterionic poly(arylene ether sulfone) (PAES) copolymers, which was blended with native polysulfone (PSf) to fabricate free-standing asymmetric membranes via non-solvent induced phase separation process. Both the porosity of the support layer and surface hydrophilicity increased drastically due to the incorporation of zwitterion functionalities in the rigid polysulfone matrix. The water permeance and antifouling ability of the blend membranes were both remarkably improved to 2.5 Lm−2 h−1 bar−1 and 94% of flux recovery ratio, respectively, while salt rejection remained at a high level (98%) even under the high exposure to chlorine (8,000 ppm•h). Besides the preliminary blended membrane design, for the future membrane property enhancement, this dissertation also focused on polymer structure optimizations via elucidating the fundamentals from two perspectives: 1). Synthetic reaction kinetics and mechanisms on polycondensation of PAES. Interestingly, in combination of experiments and the computational calculations by density functional theory (DFT) methods in this work, only the aryl chlorides (ArCl) monomer follows the classical second-order reaction kinetics of aromatic nucleophilic substitution (SNAr) mechanism, while the kinetics of the aryl fluorides (ArF) reaction fit a third-order rate law. The third order reaction behavior of the ArF monomer is attributed to the activation of the carbon-fluorine bond by two potassium cations (at least one bounded to phenolate), which associate as a strong three-body complex. This complex acts as the predominant reactant during the attack by the nucleophile. 2). Optimized copolymer structures were developed for controlled high molecular weight (Mw ~ 65 kDa) and zwitterionic charge content (0~100 mol%), via off-set stoichiometry during polycondensations, following with thiol-ene click reaction and ring-opening of sultone to introduce the sulfobetaine functional groups. The structure-property-morphology relationships were elucidated for better understanding atomic-level features in the charged polymers for future high-performance desalination applications.
Date Created
2019
Agent

Production of Biofuel from Algae and Salicornia using Hydrothermal Liquefaction (HTL) Technique

132228-Thumbnail Image.png
Description
Fossil fuels have been the primary source of energy in the world for many decades. However, they are among the top contributors of the greenhouse gas emissions in the atmosphere. The objective of this research was to produce a more

Fossil fuels have been the primary source of energy in the world for many decades. However, they are among the top contributors of the greenhouse gas emissions in the atmosphere. The objective of this research was to produce a more environmentally friendly biofuel from Algae-Helix and Salicornia biomasses. Experiments were conducted using a hydrothermal liquefaction (HTL) technique in the HTL reactor to produce biofuel that can potentially replace fossil fuel usage. Hydrothermal Liquefaction is a method used to convert the biomass into the biofuels. HTL experiments on Algae-Helix and Salicornia at 200°C-350°C and 430psi were performed to investigate the effect of temperature on the biocrude yield of the respective biomass used. The effect of the biomass mixture (co-liquefaction) of Salicornia and algae on the amount of biocrude produced was also explored. The biocrude and biochar (by-product) obtained from the hydrothermal liquefaction process were also analyzed using thermogravimetric analyzer (TGA). The maximum biocrude yield for the algae-helix biomass and for the Salicornia biomass were both obtained at 300°C which were 34.63% and 7.65% respectively. The co-liquefaction of the two biomasses by 50:50 provided a maximum yield of 17.26% at 250°C. The co-liquefaction of different ratios explored at 250°C and 300°C concluded that Salicornia to algae-helix ratio of 20:80 produced the highest yields of 22.70% and 31.97%. These results showed that co-liquefaction of biomass if paired well with the optimizing temperature can produce a high biocrude yield. The TGA profiles investigated have shown that salicornia has higher levels of ash content in comparison with the algae-helix. It was then recommended that for a mixture of algae and Salicornia, large-scale biofuel production should be conducted at 250℃ in a 20:80 salicornia to algae biocrude ratio, since it lowers energy needs. The high biochar content left can be recycled to optimize biomass, and prevent wastage.
Date Created
2019-05
Agent

Production of Biofuel from Algae and Salicornia using Hydrothermal Liquefaction (HTL) Technique

132296-Thumbnail Image.png
Description
Fossil fuels have been the primary source of energy in the world for many decades. However, they are among the top contributors of the greenhouse gas emissions in the atmosphere. The objective of this research was to produce a

Fossil fuels have been the primary source of energy in the world for many decades. However, they are among the top contributors of the greenhouse gas emissions in the atmosphere. The objective of this research was to produce a more environmentally friendly biofuel from Algae-Helix and Salicornia biomasses. Experiments were conducted using a hydrothermal liquefaction (HTL) technique in the HTL reactor to produce biofuel that can potentially replace fossil fuel usage. Hydrothermal Liquefaction is a method used to convert the biomass into the biofuels. HTL experiments on Algae-Helix and Salicornia at 200°C-350°C and 430psi were performed to investigate the effect of temperature on the biocrude yield of the respective biomass used. The effect of the biomass mixture (co-liquefaction) of Salicornia and algae on the amount of biocrude produced was also explored. The biocrude and biochar (by-product) obtained from the hydrothermal liquefaction process were also analyzed using thermogravimetric analyzer (TGA). The maximum biocrude yield for the algae-helix biomass and for the Salicornia biomass were both obtained at 300°C which were 34.63% and 7.65% respectively. The co-liquefaction of the two biomasses by 50:50 provided a maximum yield of 17.26% at 250°C. The co-liquefaction of different ratios explored at 250°C and 300°C concluded that Salicornia to algae-helix ratio of 20:80 produced the highest yields of 22.70% and 31.97%. These results showed that co-liquefaction of biomass if paired well with the optimizing temperature can produce a high biocrude yield. The TGA profiles investigated have shown that salicornia has higher levels of ash content in comparison with the algae-helix. It was then recommended that for a mixture of algae and Salicornia, large-scale biofuel production should be conducted at 250℃ in a 20:80 salicornia to algae biocrude ratio, since it lowers energy needs. The high biochar content left can be recycled to optimize biomass, and prevent wastage.
Date Created
2019-05
Agent

Gasification of Municipal Solid Waste for Hydrogen Production

Description
A Study of the gasification of municipal solid waste (MSW) for hydrogen production was completed through research and statistical design of experiment. The study was done for general syngas production with conditions of high temperature and pressure. Waste samples from

A Study of the gasification of municipal solid waste (MSW) for hydrogen production was completed through research and statistical design of experiment. The study was done for general syngas production with conditions of high temperature and pressure. Waste samples from kitchen waste including rice, avocado, and egg shells were used. Dry orange blossom tree leaves were included and a very minimal fraction of used paper and Styrofoam. One of the components of the syngas predicted was hydrogen, but this study does not discuss techniques for the separation of the hydrogen from the syngas. A few suggestions, however, such as the use of gas chromatography and membranes are made for the study of the syngas and separation of the hydrogen from the syngas. A three level, three factors-half factorial design was used to analyze the impact of pressure, residence time and temperature on the gasification of MSW through a hydrothermal gasification approach. A series 4590 micro stirred reactor of 100mL was used to gasify MSW, but first, it was established through a TGA approach that the waste was about 5% moisture content and 55% organic content (OC). The TGA device used was the TG 209 F1 Libra. Results of the gasification indicated that the most important factor in the gasification of MSW is temperature, followed by residence time and that the syngas yield increases with a decreasing pressure of the system. A thermodynamic model relating the three factors and the syngas yield was developed.
Date Created
2019-05
Agent

Can Biochar Be Converted into Activated Carbon?

132449-Thumbnail Image.png
Description
In Nepal, a viable solution for environmental management, food and water security is the production of biochar, a carbon material made of plants burned in low oxygen conditions. Currently, the biochar is manufactured into charcoal briquettes and sold on the

In Nepal, a viable solution for environmental management, food and water security is the production of biochar, a carbon material made of plants burned in low oxygen conditions. Currently, the biochar is manufactured into charcoal briquettes and sold on the market for energy usage, however this may not provide the best value for community members who make less than a dollar a day and sell the biochar for as little as 16 cents per kilogram. This thesis seeks to improve the price of biochar and help their livelihoods as well as explore innovative solutions. One way to improve biochar while addressing water security problems is to create activated carbon, which uses its heightened porosity to adsorb contaminants from water or air. Activated carbon is also worth 100x the price of biochar. This thesis evaluates the mass content of biochar produced in Nepal, comparing it to literature values, and performed gravimetric and thermogravimetric analysis, comparing it to Activated Charcoal. Analysis of the biochar system used in Nepal reveals that the byproduct of biochar, biofuels, is highly underutilized. The higher heating value of biochar is 17.95 MJ/kg, which is much lower than other charcoals which burn around 30 MJ/kg. Low volatile content, less than 5% in biochar, provides a smokeless briquette, which is favorable on the market, however low heating value and misutilizations of biofuels in the solution indicate that creating a briquette is not the best use for biochar. Ash content is really high in this biochar, averaging around 12% and it may be due to the feedstock, a composite between Mikania and Lantana, which have 5.23% and 10.77% ash content respectively. This does not necessarily indicate a poor quality biochar, since ash values can vary widely between charcoals. Producing activated charcoal from this biochar is a favored solution; it will increase the price of the biochar, provide water security solutions, and be an appropriate process for this biochar, where heating value and underutilization of biofuel byproducts pose a problem.
Date Created
2019-05
Agent

Heterogeneous Catalysis for Organic Reactions

Description
This honors thesis is focused on two separate catalysis projects conducted under the mentorship of Dr. Javier Pérez-Ramírez at ETH Zürich. The first project explored ethylene oxychlorination over supported europium oxychloride catalysts. The second project investigated alkyne semihydrogenation over nickel

This honors thesis is focused on two separate catalysis projects conducted under the mentorship of Dr. Javier Pérez-Ramírez at ETH Zürich. The first project explored ethylene oxychlorination over supported europium oxychloride catalysts. The second project investigated alkyne semihydrogenation over nickel phosphide catalysts. This work is the subject of a publication of which I am a co-author, as cited below.

Project 1 Abstract: Ethylene Oxychlorination
The current two-step process for the industrial process of vinyl chloride production involves CuCl2 catalyzed ethylene oxychlorination to ethylene dichloride followed by thermal cracking of the latter to vinyl chloride. To date, no industrial application of a one-step process is available. To close this gap, this work evaluates a wide range of self-prepared supported CeO2 and EuOCl catalysts for one-step production of vinyl chloride from ethylene in a fixed-bed reactor at 623 773 K and 1 bar using feed ratios of C2H4:HCl:O2:Ar:He = 3:3 6:1.5 6:3:82 89.5. Among all studied systems, CeO2/ZrO2 and CeO2/Zeolite MS show the highest activity but suffer from severe combustion of ethylene, forming COx, while 20 wt.% EuOCl/γ-Al2O3 leads to the best vinyl chloride selectivity of 87% at 15.6% C2H4 conversion with complete suppression of CO2 formation and only 4% selectivity to CO conversion for over 100 h on stream. Characterization by XRD and EDX mapping reveals that much of the Eu is present in non-active phases such as Al2Eu or EuAl4, indicating that alternative synthesis methods could be employed to better utilize the metal. A linear relationship between conversion and metal loading is found for this catalyst, indicating that always part of the used Eu is available as EuOCl, while the rest forms inactive europium aluminate species. Zeolite-supported EuOCl slightly outperforms EuOCl/γ Al2O3 in terms of total yield, but is prone to significant coking and is unstable. Even though a lot of Eu seems locked in inactive species on EuOCl/γ Al2O3, these results indicate possible savings of nearly 16,000 USD per kg of catalyst compared to a bulk EuOCl catalyst. These very promising findings constitute a crucial step for process intensification of polyvinyl chloride production and exploring the potential of supported EuOCl catalysts in industrially-relevant reactions.

Project 2 Abstract: Alkyne Semihydrogenation
Despite strongly suffering from poor noble metal utilization and a highly toxic selectivity modifier (Pb), the archetypal catalyst applied for the three-phase alkyne semihydrogenation, the Pb-doped Pd/CaCO3 (Lindlar catalyst), is still being utilized at industrial level. Inspired by the very recent strategies involving the modification of Pd with p-block elements (i.e., S), this work extrapolates the concept by preparing crystalline metal phosphides with controlled stoichiometry. To develop an affordable and environmentally-friendly alternative to traditional hydrogenation catalysts, nickel, a metal belonging to the same group as Pd and capable of splitting molecular hydrogen has been selected. Herein, a simple two-step synthesis procedure involving nontoxic precursors was used to synthesize bulk nickel phosphides with different stoichiometries (Ni2P, Ni5P4, and Ni12P5) by controlling the P:Ni ratios. To uncover structural and surface features, this catalyst family is characterized with an array of methods including X-ray diffraction (XRD), 31P magic-angle nuclear magnetic resonance (MAS-NMR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). Bulk-sensitive techniques prove the successful preparation of pure phases while XPS analysis unravels the facile passivation occurring at the NixPy surface that persists even after reductive treatment. To assess the characteristic surface fingerprints of these materials, Ar sputtering was carried out at different penetration depths, reveling the presence of Ni+ and P-species. Continuous-flow three-phase hydrogenations of short-chain acetylenic compounds display that the oxidized layer covering the surface is reduced under reaction conditions, as evidenced by the induction period before reaching the steady state performance. To assess the impact of the phosphidation treatment on catalytic performance, the catalysts were benchmarked against a commercial Ni/SiO2-Al2O3 sample. While Ni/SiO2-Al2O3 presents very low selectivity to the alkene (the selectivity is about 10% at full conversion) attributed to the well-known tendency of naked nickel nanoparticles to form hydrides, the performance of nickel phosphides is highly selective and independent of P:Ni ratio. In line with previous findings on PdxS, kinetic tests indicate the occurrence of a dual-site mechanism where the alkyne and hydrogen do not compete for the same site.

This work is the subject of a publication of which I am a co-author, as cited below.

D. Albani; K. Karajovic; B. Tata; Q. Li; S. Mitchell; N. López; J. Pérez-Ramírez. Ensemble Design in Nickel Phosphide Catalysts for Alkyne Semi-Hydrogenation. ChemCatChem 2019. doi.org/10.1002/cctc.201801430
Date Created
2019-05
Agent