This thesis was prepared by Tyler Maynard and Hayley Monroe, who are students at Arizona State University studying to complete their B.S.E.s in Civil Engineering and Construction Engineering, respectively. Both students are members of Barrett, the Honors College, at Arizona State University, and have prepared the following document for the purpose of completing their undergraduate honors thesis. The early sections of this document comprise a general, introductory overview of earthquakes and liquefaction as a phenomenon resulting from earthquakes. In the latter sections, this document analyzes the relationship between the furthest hypocentral distance to observed liquefaction and the earthquake magnitude published in 2006 by Wang, Wong, Dreger, and Manga. This research was conducted to gain a greater understanding of the factors influencing liquefaction and to compare the existing relationship between the maximum distance for liquefaction and earthquake magnitude to updated earthquake data compiled for the purpose of this report. As part of this research, 38 different earthquake events from the Geotechnical Extreme Events Reconnaissance (GEER) Association with liquefaction data were examined. Information regarding earthquake depth, distance to the furthest liquefaction event (epicentral and hypocentral), and earthquake magnitude (Mw) from recent earthquake events (1989 to 2016) was compared to the previously established relationship of liquefaction occurrence distance to moment magnitude. The purpose of this comparison was to determine if recent events still comply with the established relationship. From this comparison, it was determined that the established relationship still generally holds true for the large magnitude earthquakes (magnitude 7.5 or above) that were considered herein (with only 2.6% falling above the furthest expected liquefaction distance). However, this relationship may be too conservative for recent, low magnitude earthquake events; those events examined below magnitude 6.3 did not approach established range of furthest expected liquefaction distance. The overestimation of furthest hypocentral distance to liquefaction at low magnitudes suggest the empirical relationship may need to be adjusted to more accurately capture recent events, as reported by GEER.

This dissertation details an attempt to experimentally evaluate the Giroud et al. (1995) concentration factors for geomembranes loaded in tension perpendicular to a seam by laboratory measurement. Field observations of the performance of geomembrane liner systems indicates that tears occur at average strains well below the yield criteria. These observations have been attributed, in part, to localized strain concentrations in the geomembrane loaded in tension in a direction perpendicular to the seam. Giroud et al. (1995) has presented theoretical strain concentration factors for geomembrane seams loaded in tension when the seam is perpendicular to the applied tensile strain. However, these factors have never been verified. This dissertation was prepared in fulfillment of the requirements for graduation from Barrett, the Honors College at Arizona State University. The work described herein was sponsored by the National Science Foundation as a part of a larger research project entitled "NEESR: Performance Based Design of Geomembrane Liner Systems Subject to Extreme Loading." The work is motivated by geomembrane tears observed at the Chiquita Canyon landfill following the 1994 Northridge earthquake. Numerical analysis of the strains in the Chiquita Canyon landfill liner induced by the earthquake indicated that the tensile strains, were well below the yield strain of the geomembrane material. In order to explain why the membrane did fail, strain concentration factors due to bending at seams perpendicular to the load in the model proposed by Giroud et al. (1995) had to be applied to the geomembrane (Arab, 2011). Due to the localized nature of seam strain concentrations, digital image correlation (DIC) was used. The high resolution attained with DIC had a sufficient resolution to capture the localized strain concentrations. High density polyethylene (HDPE) geomembrane samples prepared by a leading geomembrane manufacturer were used in the testing described herein. The samples included both extrusion fillet and dual hot wedge fusion seams. The samples were loaded in tension in a standard triaxial test apparatus. to the seams in the samples including both extrusion fillet and dual hot wedge seams. DIC was used to capture the deformation field and strain fields were subsequently created by computer analysis.

This thesis describes the conduct and interpretation of large scale direct shear testing of municipal solid waste (MSW) which was recently conducted at Arizona State University under the guidance of Dr. Edward Kavazanjian Jr. This research was performed to establish the shear strength parameters for MSW of a particular landfill in the eastern United States. As part of this research, the unit weight of the material of interest was recorded to help establish if the properties of the waste tested in this project were consistent with the properties of MSW reported in the technical literature.
The paper begins with an overview of scholarly articles on shear strength and unit weight of MSW. This overview summarizes trends found in other MSW investigations. The findings described in these articles served as a basis to determine if the direct shear test results in this investigation complied with typical values reported in other MSW investigations.
A majority of this thesis is dedicated to describing testing protocol, nuances of experimental execution, and test results of the direct shear tests. This culminates in an analysis of the shear strength parameters and consolidated unit weight exhibited by the MSW tested herein. Throughout the testing displacement range of 3.5 inches, none of the MSW specimens achieved a peak shear stress. Consequently, the test results were analyzed at displacements of 1.7 inches, 2.1 inches, and 2.4 inches during the tests to develop Mohr-Coulomb envelopes for each specified displacement. All three envelopes indicated that the cohesion of the material was effectively 0 psf). The interpreted angles of internal friction were of 30.6°, 33.7°, and 36.0° for the displacements of 1.7, 2.1, and 2.4 inches, respectively. These values correlate well with values from previous investigations, indicating that from a shear strength basis the waste tested in this project was typical of MSW from other landfills. Analysis of the consolidated unit weight of the MSW specimens also suggests the MSW was similar to in-situ MSW which was placed in a landfill with low levels of compaction and small amounts of cover soil.

After describing the types of foundation systems employed for high rise buildings, this thesis discusses the process of foundation design for tall buildings as it is practiced today, including computer programs used in designing the foundations of high rise buildings. This thesis then presents the geotechnical in-situ and laboratory tests used to establish the parameters required for input to design analyses for high rise building foundations. This thesis subsequently describes the Construction Quality Assurance practices used in the construction of the foundations of high rise buildings. This thesis next presents several case histories detailing the foundation practices employed in the design and construction of modern high rise buildings. Finally, this thesis provides some concluding thoughts regarding the development of the geotechnical practices when designing and constructing high rise buildings.

Currently conventional Subtitle D landfills are the primary means of disposing of our waste in the United States. While this method of waste disposal aims at protecting the environment, it does so through the use of liners and caps that effectively freeze the breakdown of waste. Because this method can keep landfills active, and thus a potential groundwater threat for over a hundred years, I take an in depth look at the ability of bioreactor landfills to quickly stabilize waste. In the thesis I detail the current state of bioreactor landfill technologies, assessing the pros and cons of anaerobic and aerobic bioreactor technologies. Finally, with an industrial perspective, I conclude that moving on to bioreactor landfills as an alternative isn't as simple as it may first appear, and that it is a contextually specific solution that must be further refined before replacing current landfills.

This dissertation investigates the potential for enzyme induced carbonate cementation as an alternative to Portland cement for creating building material from sand aggregate. We create a solution of urease enzyme, calcium chloride (CaCl2), and urea in water and added sand. The urease catalyzes the synthesis of carbonate from urea, and the carbonate then bonds with a dissociated calcium ion and precipitates from the solution as calcium carbonate (CaCO3). This precipitate can form small crystal bridges at contacts between sand grains that lock the sand grains in place. Using enzyme induced carbonate precipitation we created a cemented sand sample with a maximum compressive strength of 319 kPa and an elastic modulus of approximately 10 MPa. Images from the SEM showed that a major failure mechanism in the cemented samples was the delamination of the CaCO3 from the sand grains. We observed that CaCO3 cementation did not when solutions with high concentrations of CaCl2 and urea were used.

This dissertation investigates the potential for stimulating ureolytic and denitrifying microbes concurrently (i.e., stimulating a ureolytic, denitrifying microbial community) for a more efficient microbially induced carbonate precipitation (MICP) process. Three sand columns were run for a treatment period of six weeks with a continuous flow of nutrient solution containing calcium nitrate, calcium acetate, calcium chloride, magnesium sulfate, tryptic soy broth and trace metals. The first and third columns served as control columns, within which only denitrification processes were at work. The first column was used for periodic sampling to measure the pH, ion concentrations, and total nitrogen over time. The third column was used to measure compressional (P-) and shear (S-) wave velocities to monitor cementation and desaturation over time. The second column was subject to initial conditions identical to the other two columns except that urea was added to the nutrient solution to stimulate ureolysis and was also subject to sampling. This was done to determine whether the use of the combined MICP processes resulted in increased efficiency of precipitation. Results from ion chromatography analysis, acid digestion and scanning electron microscope imaging did not show an increase in the amount of carbonate precipitated for the second column, possibly due to nitrite inhibition and abiotic hydrolysis of the urea from sterilization of the nutrient solution through autoclaving. However, the stimulation of denitrification and ureolysis in combination was achieved, and the amount of carbonate precipitation per mol of nitrate reduced increased, which in a sense increased the efficiency of the system. Ultimately, more experimentation is needed to determine if this combination is beneficial for MICP.

Recent research efforts have been directed to improve the quality of pavement design procedures by considering the transient nature of soil properties due to environmental and aging effects on pavement performance. The main purpose of this research study was to investigate the existence of subgrade soil moisture changes that may have arisen due to thermal and hydraulic gradients at the Atlantic City NAPTF and to evaluate their effect on the material stiffness and the California Bearing Ratio (CBR) strength parameter of the clay subgrade materials. Laboratory data showed that at the same water content, matric suction decreases with increasing temperature; and at the same suction, hydraulic conductivity increases with increasing temperature. Models developed, together with moisture/temperature data collected from 30 sensors installed in the test facility, yielded a maximum variation of suction in field of 155 psi and changes in hydraulic conductivity from 2.9E-9 m/s at 100% saturation to 8.1E-12 at 93% saturation. The maximum variation in temperature was found to be 20.8oC at the shallower depth and decreased with depth; while a maximum variation in moisture content was found to be 3.7% for Dupont clay and 4.4% for County clay. Models developed that predicts CBR as a function of dry density and moisture content yielded a maximum variation of CBR of 2.4 for Dupont clay and 2.9 for County clay. Additionally, models were developed relating the temperature with the bulk stress and octahedral stress applied on the subgrade for dual gear, dual tandem and triple tandem gear types for different tire loads. It was found that as the temperature increases the stresses increase. A Modified Cary and Zapata model was used for predicting the resilient modulus(Mr) of the subgrade. Using the models developed and the temperature/moisture changes observed in the field, the variation of suction, bulk and octahedral stresses were estimated, along with the resilient modulus for three different gear types. Results indicated that changes in Mr as large as 9 ksi occur in the soils studied due to the combined effect of external loads and environmental condition changes.

This dissertation presents an investigation of calcium carbonate precipitation via hydrolysis of urea (ureolysis) catalyzed by plant-extracted urease enzyme for soil improvement. In this approach to soil improvement, referred to as enzyme induced carbonate precipitation (EICP), carbonate minerals are precipitated within the soil pores, cementing soil particles together and increasing the dilatancy of the soil. EICP is a bio-inspired solution to improving the properties of cohesionless soil in that no living organisms are engaged in the process, though it uses a biologically-derived material (urease enzyme).

Over the past decade, research has commenced on biologically-mediated solutions like microbially induced carbonate precipitation (MICP) and biologically-inspired solutions like EICP for non-disruptive ground improvement. Both of these approaches rely upon hydrolysis of urea catalyzed by the enzyme urease. Under the right environmental conditions (e.g., pH), the hydrolysis of urea leads to calcium carbonate precipitation in the presence of Ca^(2+). The rate of carbonate precipitation via hydrolysis of urea can be up to 〖10〗^14 times faster than natural process.

The objective of this research was to ascertain the effectiveness of EICP for soil improvement via hydrolysis of urea (ureolysis) catalyzed by plant-extracted urease enzyme. Elements of this work include: 1) systematic experiments to identify an optimum EICP treatment solution; 2) evaluation of the mechanical properties of EICP-treated soil under different treatment conditions and with varying carbonate contents; 3) investigation of the potential for enhancing the EICP stabilization process by including xanthan gum, natural sisal fiber, and powdered of dried non-fat milk in the EICP treatment solution; and 4) bench-scale studies of the use of EICP to make sub-horizontal columns of cemented soil for soil nailing and vertical columns of cemented soil for foundation support. As part of this research, the effect of three preparation methods (mix-and-compact, percolation, and injection) was also examined as was the influence of the grain size of soil. The results of this study should help make the EICP technique an attractive option for geotechnical engineers for ground improvement and stimulate the development and use of other biogeotechnical techniques for civil engineering purposes.

Laboratory testing was conducted to quantify strain concentrations adjacent to seams and scratches in high density polyethylene (HDPE) geomembranes. The tensile strain profile of remnants meeting the ASTM criteria for wide-width tensile testing from samples of field seams recovered for construction quality assurance testing was evaluated using digital image correlation (DIC). Strains adjacent to scratches on laboratory prepared samples loaded in tension were also measured using DIC. The tensile strain in the zone adjacent to a seam and the tensile strain adjacent to a scratch were compared to the tensile strains calculated using theoretical strain concentration factors. The relationship between the maximum tensile strain adjacent to a seam and the global nominal strain in the sample was quantified for textured and smooth geomembranes of common thicknesses. Using statistical analysis of the data, bounds were developed for the allowable nominal tensile strain expected to induce maximum tensile strains adjacent to the seam less than or equal to the typical yield strain of HDPE geomembranes, at several confidence levels. Where nominal strain is the global or average strain applied to the sample and maximum strain is the largest tensile strain induced in the sample.

The reduction in the nominal yield strain due to a scratch in a HDPE geomembrane was also quantified. The yield strain was approximately the same as predicted using theoretical strain concentration factors. The difference in the average measured maximum strains adjacent to the seams of textured and smooth HDPE geomembranes was found to be statistically insignificant. However, maximum strains adjacent to extrusion welded seams were somewhat greater than adjacent to fusion welded seams for nominal strains on the order of 3% to 4%. The results of the testing program suggest that the nominal tensile strain should be limited to 4% around dual hot wedge seams and 3% around extrusion fillet seams to avoid maximum strains equal to 11%, a typical yield strain for HDPE geomembranes.