Plant Productivity of Various Plants Grown in Coffee Grounds

134712-Thumbnail Image.png
Description
Over the last century, society has begun to acknowledge and observe how human actions are negatively impacting the environment. Sustainable living is becoming more adopted into daily lives, including a focus on waste management and recycling. Previous informal studies have…

Over the last century, society has begun to acknowledge and observe how human actions are negatively impacting the environment. Sustainable living is becoming more adopted into daily lives, including a focus on waste management and recycling. Previous informal studies have proposed that coffee grounds can be recycled and added to the soil to increase plant productivity. The objective of this experiment was to test how different concentrations of roasted coffee grounds would affect the overall plant productivity when introduced in the soil of various plant types and environmental atmospheres. Three treatments were selected (100% potting mix, 50% potting mix/50% coffee grounds, and 25% potting mix/75% coffee grounds) and applied to 3 acid-tolerating plants (radish, basil, and parsley). Each of these treatments were grown in 2 different environments, where one was planted in a Tempe, AZ backyard while the other group was planted in a lab environment, locating at Arizona State University's Tempe Campus. Each plant with its respective treatments (plant type, coffee ground treatment, and environment) had 10 identical plants for statistical accuracy, resulting in a total of 180 plants grown, observed, and analyzed for this 3-month long experiment. The plant development, plant height, length of roots, quantity of leaves, and environmental observations were recorded and used to define plant productivity in this investigation. The experiment demonstrated low survival rates in all groups including the control group, suggesting a flaw in the experimental design. Nonetheless, the experiment showed that among the surviving plants, the 75% treatment had the largest negative impact on plant productivity. The measured root lengths and leaf quantity had various results across each plant group, leaving the hypothesis unverified. Overall, the experiment was effective in demonstrating negative impacts of great concentrations of coffee grounds when introduced to various plants, but further investigation with an adjusted experimental design will need to be completed to reach a reliable conclusion.
Date Created
2016-12
Agent

Prestige Worldwide Resort

134310-Thumbnail Image.png
Description
The Prestige Worldwide Resort and development area will be constructed to the east of Scottsdale Rd and North of the 101 loop. The development area is composed of 442.58 acres of land within 9 parcels. Zoning for this development area…

The Prestige Worldwide Resort and development area will be constructed to the east of Scottsdale Rd and North of the 101 loop. The development area is composed of 442.58 acres of land within 9 parcels. Zoning for this development area consists of commercial, recreational, golf course, residential, and water/wastewater treatment. The main feature of the development area is a luxury resort to be located at the southwest corner of Legacy Blvd and Hayden Rd. The resort includes a large pond over which the entrance road traverses. The resort also includes an 18-hole golf course located just north of Legacy Blvd. The proposed residential area is to the east of Hayden Rd on the northern half of the site. Along the northeastern border of this residential area are APS, SRP, and Bureau of Reclamation easements. A recreational area in the form of a park is proposed to the east and west of the southern portion of N Hayden Rd on the site. The southeast corner or the site is reserved for water and wastewater treatment. The southwest corner of the site is for commercial use with an additional recreational/sporting area just to the north of this commercial area. The key feature of the resort is its luxurious eight-story hotel along with two other hotel buildings that accommodate tourists who are visiting Scottsdale. The main hotel includes 210 rooms to provide enough housing for these tourists and acquire more attraction to Scottsdale. The composition of the hotel consists of the first floor being the lobby and a recreational area. The other floors each contain 30 rooms, 3 elevators, and a staircase. Surrounding the hotel is a parking lot for the hotel guests and people attending events hosted at the hotel. Regarding the hotel specifications, two different alternative designs were produced to determine the ideal steel member type, concrete reinforcement, and the steel frame layout. The final hotel design was determined by which alternative had the lowest structural response from loading and cost effective.
Date Created
2017-05
Agent

Physical Water Treatment Effects on Evaporation Rates, Hardness, and Microbial Life

136729-Thumbnail Image.png
Description
The rising need for water reuse in the Southwest United States has increased awareness of the quality of wastewater. This need is caused by an increased population having basic water needs; inefficient water use, such as overwatering lawns and leaking…

The rising need for water reuse in the Southwest United States has increased awareness of the quality of wastewater. This need is caused by an increased population having basic water needs; inefficient water use, such as overwatering lawns and leaking pipes; and recent drought conditions all over the southwestern US. Reclaimed water is a possible solution. It's used for a variety of non-potable, or non-drinkable, reasons. These uses include: cooling power plants, concrete mixing, artificial lakes, and irrigation for public parks and golf courts. Cooling power plants utilizes roughly 41% of the total water consumed by the United States, which makes it the highest user of water in the US. The attention is turned to optimizing mechanical processes and reducing the amount of water consumed. Wet-recirculating systems reuse cooling water in a second cycle rather than discharging it immediately. Cooling towers are commonly used to expose water to ambient air. As the water evaporates, more water is withdrawn while the rest continues to circulate. These systems have much lower water withdrawals than once-through systems, but have higher water consumption. The cooling towers in wet-recirculating plants and other warm machinery have two major limitations: evaporation of pumped water and scale formation in the components. Cooling towers circulate water, and only draw as it evaporates, which conserves water. The scale formation in the components is due to the hardness of the water. Scale occurs when hard water evaporates and forms solid calcium carbonate. This formation can lead to reduced flow or even clogging in pipes, fouling of components or pipes, and reduced cooling efficiency. Another concern from the public over the use of reclaimed water is the possibility of there being fecal contamination. This fear stems from the stigma associated with drinking water that essentially came from the toilet. An emerging technology, in order to address these three issues, is the use of an electromagnetic device. The wires have a current flowing through which induces a magnetic field perpendicular to the direction of the flow, while the electrical field is proportional to the flow velocity. In other words, the magnetic and electrical fields will create an effect that will concentrate cations at the center of the pipe and anions at the wall of the pipe or the other way depending on the direction of the flow. Reversing the field will then cause the cations and anions to move toward one another and increase the collision frequency and energy. The purpose of these experiments is to test the effects of the electromagnetic device on the aforementioned topics. There are three tests that were performed, a surface tension test, a hardness test, and a microbial test. The surface tension test focused on the angle of a water droplet until it burst. The angle would theoretically decrease as the bond between water molecules increased due to the device. The results of this test shows a lower angle for the treated water but a higher angle for the untreated one. This means the device had an effect on the surface tension of the water. Hard water is caused by calcium and magnesium ions in the water. These ions are dissolved in the water as it travels past soil and rocks. The purpose of this test is to measure the free calcium ion amount in the water. If the free calcium number lowers, then it can be assumed it collided with the carbonate and formed calcium carbonate. This calcium carbonate causes a reduction in hardness in the water. The result of the test showed no correlation between ion concentrations in the treated/untreated system. The e. coli test focused on testing the effects of an electromagnetic device on inhibiting fecal contamination in water/wastewater at a treatment facility. In order to detect fecal contamination, we test for bacteria known as fecal coliforms, more specifically e. coli. The test involved spiking the system with bacteria and testing its concentrations after time had passed.The e. coli results showed no trend in the inactivation of the bacteria. In conclusion, the device had varying results, but multiple steps can be taken in the future in order to continue research.
Date Created
2014-12
Agent

Transport of bacteria, viruses and a visual tracer in a saturated 2-dimensional porous media model

155850-Thumbnail Image.png
Description
This study was designed to provide insight into microbial transport kinetics which might be applied to bioremediation technology development and prevention of groundwater susceptibility to pathogen contamination. Several pilot-scale experiments were conducted in a saturated, 2 dimensional, packed porous media…

This study was designed to provide insight into microbial transport kinetics which might be applied to bioremediation technology development and prevention of groundwater susceptibility to pathogen contamination. Several pilot-scale experiments were conducted in a saturated, 2 dimensional, packed porous media tank to investigate the transport of Escherichia coli bacteria, P22 bacteriophage, and a visual tracer and draw comparisons and/or conclusions. A constructed tank was packed with an approximate 3,700 cubic inches (in3) of a fine grained, homogeneous, chemically inert sand which allowed for a controlled system. Sampling ports were located at 5, 15, 25, and 25 vertical inches from the base of the 39 inch saturated zone and were used to assess the transport of the selected microorganisms. Approximately 105 cells of E. coli or P22 were injected into the tank and allowed to move through the media at approximately 10.02 inches per day. Samples were collected intermittently after injection based off of an estimated sampling schedule established from the visual tracer.

The results suggest that bacteriophages pass through soil faster and with greater recovery than bacteria. P22 in the tank reservoir experienced approximately 1 log reduction after 36 hours. After 85 hours, P22 was still detected in the reservoir after experiencing a 2 log reduction from the start of the experiment. E. coli either did not reach the outlet or died before sampling, while P22 was able to be recovered. Bacterial breakthrough curves were produced for the microbial indicators and illustrate the peak concentrations found for each sampling port. For E. coli, concentrations at the 5 inch port peaked at a maximum of 5170 CFU/mL, and eventually at the 25 inch port at a maximum of 90 CFU/mL. It is presumed that E. coli might have experienced significant filtration, straining and attachment, while P22 might have experienced little adsorption and instead was transported rapidly in long distances and was able to survive for the duration of the experiment.
Date Created
2017
Agent

Saline waste use for subgrade soil improvement

155740-Thumbnail Image.png
Description

Chloride solutions have historically been used to stabilize roads and to prevent dust; however, very little work has been done on investigating the soil stabilizing benefits from interactions between salt solutions and different soil types. The primary goal of this…

Chloride solutions have historically been used to stabilize roads and to prevent dust; however, very little work has been done on investigating the soil stabilizing benefits from interactions between salt solutions and different soil types. The primary goal of this research was to analyze the feasibility of utilizing a salt waste product as an economically and environmentally responsible means of dust control and/or soil stabilization. Specifically, this study documents an investigation leading to the understanding of how the addition of saline based waste products, when using a soil stabilizer, modifies the strength behavior of soils.

The scope of work included the evaluation of current literature, examination of the main challenges meeting relevant governmental regulations, and exploring the possibility of using saline waste to improve roadways.

Three soils were selected, treated with varying amounts of salt (calcium chloride, CaCl2), and tests included soil composition and classification, correlation of soil characteristics and salt, and obtaining strength parameters that are typically used in pavement design and analysis. The work effort also included the determination of the optimum dosage of salt concentration for each soil. Because Lime treatment is also commonly used in soil stabilization, one of the soils in this study included a treatment with Lime for comparison purposes.

Results revealed that when salt concentration was increased, a decrease in the plasticity index was observed in all soils. A modest to considerable strength gain of the treated material was also observed for two of the soils; however, a strength loss was observed for the third soil, which was attributed to its low clay content.

When comparing the soil corrosive potential, the additional salt treatment showed promise for increasing strength, to an extent; however, it changes the chemical properties of the soil. The soils prior to treatment were corrosive, which could be managed with appropriate techniques, but the salt increases the values to levels that could be potentially cost prohibitive if salt was used by itself to treat the soil.

The pavement design and performance investigation revealed that the Vineyard soil treated at 16% CaCl2 had an improvement that is comparable to the Lime treatment. On the other hand, the Eager soil showed very little pavement performance improvement at 8% CaCl2; this goes back to the effect of acid on the clay mineralogy. It was also postulated that using salt by-products to stabilize highway shoulders could be beneficial and save a lot of maintenance money when it comes to cleaning unwanted vegetation. A salt saturated soil structure could help in dust control as well.

Future environmental challenges for salt leaching that could affect agriculture in developing countries will still need to be carefully considered. The chlorine levels in the soil would increase, and if not treated, can potentially have corrosive effects on buried structures. Future research is recommended in this area and to also evaluate soil stabilizing properties of varying proportions of Lime and salt using the approach provided in this study.

Date Created
2017
Agent

Study of a Two Species Microbial Community by an Inferential Comparative Genomic Analysis Tool: Spatial Analytical Microbial Imaging

128425-Thumbnail Image.png
Description

Most molecular fingerprinting techniques, including denaturing gradient gel electrophoresis (DGGE) [1], comparative genomic hybridization (CGH) [2], real-time polymerase chain reaction (RT-PCR) [3], destroy community structure and/or cellular integrity, therefore lost the info. of the spatial locus and the in situ…

Most molecular fingerprinting techniques, including denaturing gradient gel electrophoresis (DGGE) [1], comparative genomic hybridization (CGH) [2], real-time polymerase chain reaction (RT-PCR) [3], destroy community structure and/or cellular integrity, therefore lost the info. of the spatial locus and the in situ genomic copy number of the cells. An alternative technique, fluorescence in situ hybridization (FISH) doesn't require sample disintegration but needs to develop specific markers and doesn't provide info. related to genomic copy number.

Here, a microbial analysis tool, Spatial Analytical Microbial Imaging (SAMI), is described. An application was performed with a mixture of Synechocystis sp. PCC 6803 and E. coli K-12 MG1655. The intrinsic property of their genome, reflected by the average fluorescence intensity (AFI), distinguished them in 3D. And their growth rates were inferred by comparing the total genomic fluorescence binding area (GFA) with that of the pure culture standards. A 93% of accuracy in differentiating the species was achieved.
• SAMI does not require sample disintegration and preserves the community spatial structure.
• It measures the 3D locus of cells within the mixture and may differentiate them according to the property of their genome.
• It allows assessment of the growth rate of the cells within the mixture by comparing their genomic copy number with that of the pure culture standards.

Date Created
2015-06-25
Agent

Graphene oxide mixed matrix membranes for improved desalination performance

155562-Thumbnail Image.png
Description
Reverse osmosis (RO) membranes are considered the most effective treatment to remove salt from water. Specifically, thin film composite (TFC) membranes are considered the gold standard for RO. Despite TFC membranes good performance, there are drawbacks to consider including: permeability-selectivity…

Reverse osmosis (RO) membranes are considered the most effective treatment to remove salt from water. Specifically, thin film composite (TFC) membranes are considered the gold standard for RO. Despite TFC membranes good performance, there are drawbacks to consider including: permeability-selectivity tradeoff, chlorine damage, and biofouling potential. In order to counter these drawbacks, polyamide matrixes were embedded with various nanomaterials called mixed matrix membranes (MMMs) or thin film nanocomposites (TFNs). This research investigates the use of graphene oxide (GO) and reduced graphene oxide (RGO) into the polyamide matrix of a TFC membrane. GO and RGO have the potential to alter the permeability-selectivity trade off by offering nanochannels for water molecules to sieve through, protect polyamide from trace amounts of chlorine, as well as increase the hydrophilicity of the membrane thereby reducing biofouling potential. This project focuses on the impacts of GO on the permeability selectivity tradeoff. The hypothesis of this work is that the permeability and selectivity of GO can be tuned by controlling the oxidation level of the material. To test this hypothesis, a range of GO materials were produced in the lab using different graphite oxidation methods. The synthesized GOs were characterized by X-ray diffraction and X-ray photoelectron microscopy to show that the spacing is a function of the GO oxygen content. From these materials, two were selected due to their optimal sheet spacing between 3.4 and 7 angstroms and embedded into desalination MMM. This work reveals that the water permeability coefficient of MMM embedded with GO and RGO increased significantly; however, that the salt permeability coefficient of the membrane also increased. Future research directions are proposed to overcome this limitation.
Date Created
2017
Agent

Implementation of emerging technologies: treatment capability of peracetic acid and ultraviolet irradiation

155481-Thumbnail Image.png
Description
Advanced oxidation processes (AOP’s) are water/wastewater treatment processes simultaneously providing disinfection and potential oxidation of contaminants that may cause long-term adverse health effects in humans. One AOP involves injecting peracetic acid (PAA) upstream of an ultraviolet (UV) irradiation reactor. …

Advanced oxidation processes (AOP’s) are water/wastewater treatment processes simultaneously providing disinfection and potential oxidation of contaminants that may cause long-term adverse health effects in humans. One AOP involves injecting peracetic acid (PAA) upstream of an ultraviolet (UV) irradiation reactor. Two studies were conducted, one in pilot-scale field conditions and another under laboratory conditions. A pilot-scale NeoTech UV reactor (rated for 375 GPM) was used in the pilot study, where a smaller version of this unit was used in the laboratory study (20 to 35 GPM). The pilot study analyzed coliform disinfection and also monitored water quality parameters including UV transmittance (UVT), pH and chlorine residual. Pilot study UV experiments indicate the unit is effectively treating flow streams (>6 logs total coliforms) twice the 95% UVT unit capacity (750 GPM or 17 mJ/cm2 UV Dose). The results were inconclusive on PAA/UV inactivation due to high data variability and field operation conditions creating low inlet concentrations.Escherichia coli (E. coli) bacteria and the enterobacteria phage P22—a surrogate for enteric viruses—were analyzed. UV inactivated >7.9 and 4 logs of E. coli and P22 respectively at a 16.8 mJ/cm2 UV dose in test water containing a significant organics concentration. When PAA doses of 0.25 and 0.5 mg/L were injected upstream of UV at approximately the same UV Dose, the average E.coli log inactivation increased to >8.9 and >9 logs respectively, but P22 inactivation decreased to 2.9 and 3.0 logs, respectively. A bench-scale study with PAA was also conducted for 5, 10 and 30 minutes of contact time, where 0.25 and 0.5 mg/L had <1 log inactivation of E. coli and P22 after 30 minutes of contact time. In addition, degradation of the chemical N-Nitrosodimethylamine (NDMA) in tap water was analyzed, where UV degraded NDMA by 48 to 97% for 4 and 0.5 GPM flowrates, respectively. Adding 0.5 mg/L PAA upstream of UV did not significantly improve NDMA degradation.

The results under laboratory conditions indicate that PAA/UV have synergy in the inactivation of bacteria, but decrease virus inactivation. In addition, the pilot study demonstrates the applicability of the technology for full scale operation.
Date Created
2017
Agent

Light-dependent growth kinetics and mathematical modeling of synechocystis sp. PCC 6803

155284-Thumbnail Image.png
Description
One solution to mitigating global climate change is using cyanobacteria or single-celled algae (collectively microalgae) to replace petroleum-based fuels and products, thereby reducing the net release of carbon dioxide. This work develops and evaluates a mechanistic kinetic model for…

One solution to mitigating global climate change is using cyanobacteria or single-celled algae (collectively microalgae) to replace petroleum-based fuels and products, thereby reducing the net release of carbon dioxide. This work develops and evaluates a mechanistic kinetic model for light-dependent microalgal growth. Light interacts with microalgae in a variety of positive and negative ways that are captured by the model: light intensity (LI) attenuates through a microalgal culture, light absorption provides the energy and electron flows that drive photosynthesis, microalgae pool absorbed light energy, microalgae acclimate to different LI conditions, too-high LI causes damage to the cells’ photosystems, and sharp increases in light cause severe photoinhibition that inhibits growth. The model accounts for all these phenomena by using a set of state variables that represent the pooled light energy, photoacclimation, PSII photo-damage, PSII repair inhibition and PSI photodamage. Sets of experiments were conducted with the cyanobacterium Synechocystis sp. PCC 6803 during step-changes in light intensity and flashing light. The model was able to represent and explain all phenomena observed in the experiments. This included the spike and depression in growth rate following an increasing light step, the temporary depression in growth rate following a decreasing light step, the shape of the steady-state growth-irradiance curve, and the “blending” of light and dark periods under rapid flashes of light. The LI model is a marked improvement over previous light-dependent growth models, and can be used to design and interpret future experiments and practical systems for generating renewable feedstock to replace petroleum.
Date Created
2017
Agent

Development of an optimized fitting routine for comparing theoretical data with experiments on moisture sensitive beads for carbon dioxide capture

154731-Thumbnail Image.png
Description
Carbon dioxide (CO2) is one of the most dangerous greenhouse gas. Its concentration in the atmosphere has increased to very high levels since the industrial revolution. This continues to be a threat due to increasing energy demands. 60% of the…

Carbon dioxide (CO2) is one of the most dangerous greenhouse gas. Its concentration in the atmosphere has increased to very high levels since the industrial revolution. This continues to be a threat due to increasing energy demands. 60% of the worlds global emissions come from automobiles and other such moving sources. Hence, to stay within safe limits, it is extremely important to curb current emissions and remove those which have already been emitted. Out of many available technologies, one such technology is the moisture swing based air capture technology that makes use of resin material that absorbs CO2 when it is dry and releases it when it is wet. A mathematical model was developed to better understand the mechanism of this process. In order to validate this model, numerical simulation and experimentation was done. Once the mechanism was proved, it was seen that there are many factors and parameters that govern this process. Some of these do not have definite value. To find the best fit value for these parameters, an optimized fitting routine needs to be developed that can minimize the standard deviation of the error. This thesis looks into ways in which the optimization of parameters can be done and the possible future work by using substantial data.
Date Created
2016
Agent
Subscribe to Fox, Peter